datasheet 400khz 60v 2a switching current boost led constant current driver XL6003 rev 1.6 www.xlsemi.com 1 features n wide 3.6v to 24v input voltage range n 0.22v fb adjustable led drive current n directly drive 6 series 1w led at vin>=12v n fixed 400khz switching frequency n max. 2a switching current capability n up to 92% efficiency n excellent line and load regulation n en pin ttl shutdown capability & with pwm dimming function n internal optimize power mosfet n built in soft-start function n built in frequency compensation n built in thermal shutdown function n built in current limit function n available in sop8 package applications n led lighting n boost constant current driver n monitor led backlighting n 7 to 15 lcd panels general description the XL6003 regulator is fixed frequency pwm boost (step-up) led constant current driver, capable of driving series 1w led units with excellent line and load regulation. the regulator is simple to use because it includes internal frequency compensation and a fixed-frequency oscillator so that it requires a minimum number of external components to work. the XL6003 could directly drive 6 series 1w led units at vin>12v . the pwm control circuit is able to adjust the duty ratio linearly from 0 to 95%. an enable function, an over current protection function is built inside. an internal compensation block is built in to minimize external component count. figure1. package type of XL6003 free datasheet http://
datasheet 400khz 60v 2a switching current boost led constant current driver XL6003 rev 1.6 www.xlsemi.com 2 pin configurations XL6003 1 3 5 2 4 sw en fb vin nc 6 7 8 sw gnd gnd figure2. pin configuration of XL6003 (top view) table 1 pin description pin number pin name description 1 en enable pin. drive en pin low to turn off the device, drive it high to turn it on. floating is default high. 2 vin supply voltage input pin. XL6003 operates from a 3.6v to 24v dc voltage. bypass vin to gnd with a suitably large capacitor to eliminate noise on the input. 3 fb feedback pin (fb). the feedback threshold voltage is 0.22v. 4 nc no connected. 5,6 sw power switch output pin (sw). output is the switch node that supplies power to the output. 7,8 gnd ground pin. free datasheet http://
datasheet 400khz 60v 2a switching current boost led constant current driver XL6003 rev 1.6 www.xlsemi.com 3 function block figure3. function block diagram of XL6003 typical application circuit figure4. XL6003 typical application circuit free datasheet http://
datasheet 400khz 60v 2a switching current boost led constant current driver XL6003 rev 1.6 www.xlsemi.com 4 ordering information part number marking id lead free lead free packing type XL6003e1 XL6003e1 tube package temperature range XL6003tre1 XL6003e1 tape & reel xlsemi pb-free products, as designated with e1 suffix in the par number, are rohs compliant. absolute maximum ratings note1 parameter symbol value unit input voltage vin -0.3 to 26 v feedback pin voltage v fb -0.3 to vin v en pin voltage v en -0.3 to vin v output switch pin voltage v output -0.3 to 60 v power dissipation p d internally limited mw thermal resistance (sop8) (junction to ambient, no heatsink, free air) r ja 100 o c/w operating junction temperature t j -40 to 125 o c storage temperature t stg -65 to 150 o c lead temperature (soldering, 10 sec) t lead 260 o c esd (hbm) >2000 v note1: stresses greater than those listed under maximum ratings may cause permanent damage to the device. this is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operation is not implied. exposure to absolute maximum rating conditions for extended periods may affect reliability. free datasheet http://
datasheet 400khz 60v 2a switching current boost led constant current driver XL6003 rev 1.6 www.xlsemi.com 5 XL6003 electrical characteristics t a = 25 ;unless otherwise specified. symbol parameter test condition min. typ. max. unit system parameters test circuit figure4 vfb feedback voltage vin = 5v to 12v, vout=24v iload=100ma 209 220 231 mv efficiency ? vin=12v ,vout=24v iout=0.3a - 92 - % electrical characteristics (dc parameters) vin = 12v, gnd=0v, vin & gnd parallel connect a 100uf/50v capacitor; iout=100ma, t a = 25 ; the others floating unless otherwise specified. parameters symbol test condition min. typ. max. unit input operation voltage vin 3.6 24 v shutdown supply current i stby v en =0v 70 100 ua quiescent supply current i q v en =2v, v fb =vin 2.5 5 ma oscillator frequency fosc 320 400 480 khz switch current limit i l v fb =0 2 a output power nmos rdson vin=12v, i sw =2a 110 120 mohm en pin threshold v en high (regulator on) low (regulator off) 1.4 0.8 v i h v en =2v (on) 3 10 ua en pin input leakage current i l v en =0v (off) 3 10 ua max. duty cycle d max v fb =0v 90 % free datasheet http://
datasheet 400khz 60v 2a switching current boost led constant current driver XL6003 rev 1.6 www.xlsemi.com 6 schottky diode selection table current surface mount through hole vr (the same as system maximum input voltage) 20v 30v 40v 50v 60v 1a 1n5817 1n5818 1n5819 1n5820 1n5821 1n5822 mbr320 mbr330 mbr340 mbr350 mbr360 sk32 sk33 sk34 sk35 sk36 30wq03 30wq04 30wq05 31dq03 31dq04 31dq05 3a sr302 sr303 sr304 sr305 sr306 typical system application for vin=5v to driver 3 x 1w series led units XL6003 c in 47uf /16v d1 sk34 l 22uh/2a +5v 2 7,8 1 3 5,6 gnd vin sw fb en on off 350ma i led =0.22/rs series 3 1w led rs c out 47uf/35v figure5. XL6003 system parameters test circuit (5v ~ 3 x 1w led) free datasheet http://
datasheet 400khz 60v 2a switching current boost led constant current driver XL6003 rev 1.6 www.xlsemi.com 7 typical system application for vin>=12v to driver 6 x 1w series led units figure6. XL6003 system parameters test circuit (12v ~ 6 x 1w led) typical system application for vin>=12v to driver 6 series x 28 parallel white led array figure7. XL6003 system parameters test circuit (12v ~ 6 x 28 white led) free datasheet http://
datasheet 400khz 60v 2a switching current boost led constant current driver XL6003 rev 1.6 www.xlsemi.com 8 typical system application for sepic buck-boost led driver figure8. XL6003 system parameters test circuit (buck-boost led driver) typical system application for vin>=12v to driver 6 x 1w series led units with dimming function figure9. XL6003 system parameters test circuit (12v ~ 6 x 1w led with dimming function) free datasheet http://
datasheet 400khz 60v 2a switching current boost led constant current driver XL6003 rev 1.6 www.xlsemi.com 9 package information sop8 package mechanical dimensions free datasheet http://
|
